# of Displayed Technologies: 10 / 10

Applied Category Filter (Click To Remove): Other


Categories

Containment System for Heating and Off-Gassing
TS-065424 — Due to environmental concerns and the decreasing supply of fossil fuels, there is substantial demand for nuclear-based energy production. Nuclear energy now provides about 10% of the world's electricity from about 440 power reactors and is the second largest source of low-carbon power. In addition, over 50 smaller countries utilize nuclear energy in about 220 research-size reactors. These reactors are used to produce medical and industrial isotopes and several other purposes.
It is essential to meet the safeguard requirements in liquid-fueled molten salt reactors, fuel salt transportation, and fuel cycle processes and to develop effective methods for measuring and monitoring the mass of molten fuel salt or coolant salt. However, due to the complex and dynamic nature o…
  • College: College of Engineering (COE)
  • Inventors: Van Zile, Matthew; Cao, Lei Raymond; Kauffman, Andrew
  • Licensing Officer: Zinn, Ryan

Fluid Active Flow Control Enabled Variable Turbine Vane
TS-065423 — Turbine aircraft engines (jet engines) are a type of propulsion system commonly used in aviation. These engines operate on jet propulsion, where air is drawn into the engine, mixed with fuel, ignited, and then expelled at high speed to generate thrust. Jet engines are used in commercial and military aircraft, as well as helicopters.
While turbine aircraft engines offer higher efficiency and performance than their counterparts, there is still a need to improve efficiency and reduce fuel consumption and greenhouse gases. It’s estimated that jet engines account for over 2.5% of all CO2 emissions, and there are substantial …
  • College: College of Engineering (COE)
  • Inventors: Spens, Alexander; Bons, Jeffrey
  • Licensing Officer: Zinn, Ryan

Highly Efficient Light Olefin Selectivity & Production Process
TS-065422 — Light olefins, such as ethylene and propylene, are essential building blocks in the petrochemical industry and have a wide range of uses in various applications. The most common uses for olefins include polymers, chemical intermediates, solvents, rubber, and nanomaterials, among others.
Although Light olefins are used globally in many products, the catalytic processes to produce them are energy intensive with a large carbon footprint and the production of greenhouse gases and water pollution. As a result, substantial efforts are being made in the industry to develop more sustain…
  • College: College of Engineering (COE)
  • Inventors: Ozkan, Umit; Gunduz, Seval; Kim, Jaesung
  • Licensing Officer: Zinn, Ryan

Optimal Scheduling with Energy Costs
TS-063305 — Energy use is a major concern for many industrial and manufacturing companies. Given the cost of energy and the increasing importance green energy policies, it is critical that manufacturers understand how their energy usage can be performed in a way that minimizes cost and environmental impact. …
  • College: College of Engineering (COE)
  • Inventors: Posner, Marc; Hall, Nicholas
  • Licensing Officer: Zinn, Ryan

Integrated High Power On-board Charger for Electric Vehicles
TS-063283 — As the adoption of electric vehicles (EVs) becomes more widespread, there is an increasing emphasis on improving charging technologies. There is substantial commercial need for technologies that sit on-board EVs, enhancing charging efficiency and reducing mechanical complexity. The Ohio State U…
  • College: College of Engineering (COE)
  • Inventors: Wang, Jin
  • Licensing Officer: Ashouripashaki, Mandana

"Flexible biomarker biofluid cell array for 2D/3D mapping of biomarker concentration levels"
TS-062483 — Measurement/detection of analytes (e.g., biomarkers) in different environments (e.g., biofluids/organs) is typically performed using a biosensor. Available bio-integrated sensors do not provide the capability to map biomarker concentrations, require a power source to function, use a limited number of electrodes, and normally can only measure a specific type of biofluid but not others. The use of glutamate mapping technology (radioactive or fluorescent ligand bound to a glutamate receptor) has been evaluated and found to require bulky/expensive medical equipment, a power source for measurement, cannot be miniaturized or integrated into a bio tissue, and require patients to be stationary during measurement.
The Need To address concerns and limitations with current biomarker detection/ measurement technologies, an alternative, cost-effective, efficient biosensing system/device capable of 2D/3D mapping the concentrations of various biomarkers in different bio environments is required. The Technology …
  • College: College of Engineering (COE)
  • Inventors: Li, Jinghua; Liu, Tzu Li; Nithianandam, Prasad
  • Licensing Officer: Ashouripashaki, Mandana

Porous inorganic-organic material for removal of trace carbon dioxide from air or other gas streams
TS-059305 — A novel method in which nucleophilic transition metal hydroxide groups are generated at the internal pore surfaces of MOFs to facilitate selective gas-phase CO2 fixation at low pressures via formation of metal bicarbonate species.
Metal-organic frameworks (MOFs) are porous polymers constructed by self-assembly of organic and inorganic components. They have been extensively studied for gas storage and separation applications, and post-combustion CO2 capture under flue gas conditions has been a particularly intense area of st…
  • College: College of Arts & Sciences
  • Inventors: Wade, Casey; Bien, Caitlin; Cai, Zhongzheng
  • Licensing Officer: Willson, Christopher

A Model Based Assessment Approach and an Automation Environment for Qualification of Embedded Digital Devices
TS-042856 — A Framework and Automatization process designed to determine the functionality of Embedded Digital Devices.
As our technology becomes increasingly complex, so does the quantity and variation of the Embedded Digital Device [EDD] components that are required within the project. Because not every device is made perfectly to specifications due to a propagation of random error, it is important to have a dive…
  • College: College of Engineering (COE)
  • Inventors: Smidts, Carol; Diao, Xiaoxu; Li, Boyuan
  • Licensing Officer: Hampton, Andrew

Semi-crystalline Polymer Nanocomposite and Foam Structure and Method for Making the Same
TS-038002 — A new way to create polymer nanocomposite foam structures with enhanced mechanical properties.
Nanotechnology is a constantly growing field, and has a vast potential to change the world for the better. One of the many things products that the nanotechnology field has given to us is the polymer nanocomposite and their foams. This foam has a greater value than traditional plastic foams, since…
  • College: College of Engineering (COE)
  • Inventors: Lee, L James; Chiu, Debbie Yven; Fu, Dajiong; Li, Dachao; Yen, Ying-Chieh
  • Licensing Officer: Zinn, Ryan

System for Measuring Nitric Oxide in Breath Vapor
TS-030498 — A novel system that selectively detects nitric oxide and generates a voltage indicating the measured amount.
Nitric oxide plays an important role in the biological system of living organisms. Nitiric oxide has been shown to regulate and mediate numerous processes in the nervous, immune, and cardiovascular systems by transmitting signals throughout the body. It is used within the cardiovascular system to …
  • College: College of Arts & Sciences
  • Inventors: Dutta, Prabir; Mondal, Suvra
  • Licensing Officer: Zinn, Ryan

Loading icon